ahmedhosni2002
03.07.2006, 15:28
I've made about 7 x65 siemens accessories for now.
- Three 3.5mm audio converters
- Two USB DCA-540 data cables
- One Car charger
- One Aikon to Siemens charger adapter (u know Siemens phones & chargers are rare in Egypt)
One major obstacle when creating an accessory is the connector, I had to search for an old headset or data cable for just cutting its slim lumberg connector.
But I managed to create my own (Open source :D) connectors from nothing.
So, I checked all cables & wires in my garage & found it :D. It's a cable like ones inside:
1- CD-ROM drives (I had two dead ones)
2- CD players (an old Sony Hi-Fi)
3- Inkjet printers (a dead Epson)
it's the only suitable type because the distance between its wires is the same as it's between those in the phone connector
like this one
http://www.up4world.com/images/images/5955c2f469.jpg
=================================
for one slim lumberg, you need about 4CM long, 14-wire wide of this cable in average.
I could get about 3 Meters of this cable
Phone connector needs 12 wires, but you'll cut a 14-wire wide piece of this cable (the extra 2 wires are not to be connected, but for best fit into phone)
Then it's easy to (expose) the 12 wires at both ends
http://www.up4world.com/images/images/1199cb4b41.jpg
--------
Then find or make a (base) of plastic or rubber with diemensions fitting into the phone. Glue the cable over the plastic base.
That's all
My first DCA-540 (PC side directly connected to motherboard)
http://www.up4world.com/images/images/d460e0d250.jpg
http://www.up4world.com/images/images/60b5426d86.jpg
3.5mm converter under construction ;)
http://www.up4world.com/images/images/4edbaca989.jpg
http://www.up4world.com/images/images/c7a9ab4068.jpg
http://www.up4world.com/images/images/80050fbd33.jpg
http://www.up4world.com/images/images/78dc198f61.jpg
- Three 3.5mm audio converters
- Two USB DCA-540 data cables
- One Car charger
- One Aikon to Siemens charger adapter (u know Siemens phones & chargers are rare in Egypt)
One major obstacle when creating an accessory is the connector, I had to search for an old headset or data cable for just cutting its slim lumberg connector.
But I managed to create my own (Open source :D) connectors from nothing.
So, I checked all cables & wires in my garage & found it :D. It's a cable like ones inside:
1- CD-ROM drives (I had two dead ones)
2- CD players (an old Sony Hi-Fi)
3- Inkjet printers (a dead Epson)
it's the only suitable type because the distance between its wires is the same as it's between those in the phone connector
like this one
http://www.up4world.com/images/images/5955c2f469.jpg
=================================
for one slim lumberg, you need about 4CM long, 14-wire wide of this cable in average.
I could get about 3 Meters of this cable
Phone connector needs 12 wires, but you'll cut a 14-wire wide piece of this cable (the extra 2 wires are not to be connected, but for best fit into phone)
Then it's easy to (expose) the 12 wires at both ends
http://www.up4world.com/images/images/1199cb4b41.jpg
--------
Then find or make a (base) of plastic or rubber with diemensions fitting into the phone. Glue the cable over the plastic base.
That's all
My first DCA-540 (PC side directly connected to motherboard)
http://www.up4world.com/images/images/d460e0d250.jpg
http://www.up4world.com/images/images/60b5426d86.jpg
3.5mm converter under construction ;)
http://www.up4world.com/images/images/4edbaca989.jpg
http://www.up4world.com/images/images/c7a9ab4068.jpg
http://www.up4world.com/images/images/80050fbd33.jpg
http://www.up4world.com/images/images/78dc198f61.jpg